Reduced-Emission Engine Technology - Caring for Nature
The STIHL Inc. “Caring for Nature” seal identifies its powered products that are more environmentally conscious, producing zero or low exhaust emissions. STIHL Inc. defines “low exhaust emissions” as being cleaner than EPA and/or CARB exhaust emission standards.
The decompression valve reduces the compression in the combustion chamber during cranking and helps reduce the effort needed to pull the starter rope.
IntelliCarb™ Compensating Carburetor
The IntelliCarb™ Compensating Carburetor is designed to automatically adjust the air/fuel ratio when the air filter becomes restricted or partially clogged and maintains the engine’s correct RPM. IntelliCarb™ uses air from the clean side of the air filter to control the diaphragm and flow of fuel. As the air filter becomes dirty and less air is available for the carburetor, the IntelliCarb™ system adjusts the fuel flow to compensate for the decrease in air flow. This is in contrast to typical carburetors that utilize this air from the “dirty” side of the air box.
X2 Air Filtration System
The X2 Air Filtration System revolutionizes the cut-off machine industry by allowing air filters to last up to a year, based on cutting conditions. Outside air enters the system in a swirling motion, removing 80% of dust particles. This pre-cleaned air is then routed through the primary and secondary air filters before being sent into the engine. The X2 Air Filtration System is virtually maintenance free and maintains an incredible 99.96% cleaning efficiency.
Semi-Automatic Belt Tensioning
With consistent, semi-automatic re-tensioning, this feature increases the service life of the belts and shaft bearings.
STIHL has developed a system for minimizing the vibration levels of handheld outdoor power equipment. The STIHL anti-vibration system helps reduce operator fatigue and provides a more comfortable working experience.
The ElastoStart™ starter handle is a feature of STIHL. It is a starting grip with a built-in shock absorber that helps reduce the effort when pulling on the starter cord. The ElastoStart™ starter grip noticeably reduces the sudden peak forces (compression) normally felt during cranking. The forces which occur at the grip after the first compression stroke are smoothed out.
The ergonomic top-handle bar design provides an optimal comfortable grip in any working position.
Common Features for Gasoline-Powered STIHL Cutquik® Cut-off Machines
View the features common to many gasoline-powered STIHL Cutquik® Cut-off Machines.
STIHL products sold through U.S. STIHL Dealers are for distribution in the United States only.
HP Ultra 2-Cycle Engine OilHP Ultra is a fully synthetic 2-cycle engine oil specially suited for high performance chainsaws and power tools. This oil has outstanding engine cleaning characteristics, plus “ultra” superior lubricating qualities in comparison to other 2-cycle engine oils. It is ideal for use in STIHL 4-MIX® engines. This oil is biodegradable, degrading by 80% in 21 days.
•2.6 oz. bottle makes 1 gallon mix
•5.2 oz. bottle makes 2 gallon mix
•6.4 oz. bottle makes 2 1/2 gallon mix
•12.8 oz. bottle makes 5 gallon mix
STIHL recommends a mix of 50:1 high-quality 89 octane or higher unleaded gasoline to STIHL engine oil. This same mix ratio should be used during break-in.
No-Spill® Fuel ContainersThe latest advance in gasoline can technology is here with No-Spill® fuel containers. Featuring a special treated body for low permeation, thumb-button flow controls for easier pouring, and a wide and stable base design to reduce upsets, No-Spill® fuel containers help ensure that the gasoline goes into your tank, not on the ground or into the air. Fill even smaller-sized tanks without spilling – flow stops automatically when the tank becomes full. With 1¼-gallon, 2 ½-gallon and 5-gallon sizes available, you’re sure to find one that fits your needs. Ask your local STIHL Dealer about No-Spill® fuel containers. Don’t settle for anything less.
Meets California Air Resources Board Phase II requirements for sale or use in California. No-Spill® gasoline cans are tested and certified to ASTM F-852-99 standard specification for portable gasoline containers for consumer use and our diesel and kerosene cans are tested and certified to ASTM F-976-02 standard specification for portable kerosene and diesel containers for consumer use.
Anti-Vibration GlovesReduced vibration from handheld machines. Meets ISO 10819.1996 and ANSI S2.73 vibration standards TRM 72 and TRN 55.
Sizes available: L, XL
Construction Hard Hat SystemSTIHL® Construction Hard Hat System
Also available as a hard hat only.
Note: Goggles or protective glasses meeting ANSI Standard Z87.1 must be worn under face screen and shield for primary eye protection
Leather ChapsApron style chap, designed for use with cut-off machines. These chaps are made of top quality leather that provides maximum protection and is abrasion, spatter and spark resistant. Has quick release plastic buckles and easily adjustable nylon straps.
Reserve with STIHL Express for In-Store Pick Up
With STIHL Express, you can reserve the STIHL product you need right from your home or office and pick it up at your local STIHL Dealer.
- Compare STIHL products online 24 hours a day, 7 days a week.
- Pick up products assembled and ready to go
- Get the ease of reserving online while still having access to advice from your local STIHL Dealer.
Distributor Suggested Retail Price
Buy Now for Home Delivery
STIHL OUTFITTERS™ goods are sold and shipped by authorized STIHL OUTFITTERS™ Licensees. Ordering online is easy and items can be delivered directly to your address.
Show off your STIHL pride today!
TS 800 STIHL Cutquik® Description
The TS 800 STIHL Cutquik® cut-off machine now features a magnesium guard, making it a full 0.7 pounds lighter. The TS 800 is the largest size we offer in a handheld design, featuring a 16” cutting wheel with a maximum cutting depth of 5.6”. This machine offers great flexibility – use it as a handheld or quickly snap into a cart for long, straight, controlled cuts. It’s also fuel efficient, with enough power to cut through asphalt, concrete, rebar, iron and steel with ease. The TS 800 features an ergonomic design and five-point advanced vibration control system built right into the handle, maximizing comfort so you can power through your day with less fatigue. It’s the ideal choice for professional contractors, road crews and municipalities. Visit our Dealership and feel the weight difference for yourself.